AGNEWS WATER PUTTY
Multi-Purpose Filler & Floor Leveler
Plaster Board | Concrete | Wood | Cement Sheet
Agnew’s Water Putty, the original and the best since 1929
Agnew’s Water Putty is an excellent filler for patching and leveling wood, plasterboard, cement sheet, concrete, etc. Particularly suitable if you need a hardwearing surface. Agnew’s Water Putty sets hard, adheres permanently and fills to any depth without shrinking or cracking. It can be sawn, drilled and sanded.
Agnew’s Water Putty is also ideal for Architectural and Hobby Moulding. Agnew’s Water Putty is not a flexible compound. Use only in an exterior situation if you have ensured that the substrate has a low propensity to expand and contract as the ambient temperature changes and have ensured that the Water Putty is dry and then sealed.
Agnew's Water Putty is proudly 100% Australian owned and made since 1929.
FEATURES & BENEFITS
Agnew’s Water Putty features
Use Agnew’s Water Putty for lasting repairs
Agnew’s Water Putty is great for repairs because it sticks and stays put. Plus, it’s easy to use, dries rock hard, and never shrinks. It fills voids completely and is ideal for wood repair and plaster patches.
Fill Holes In Wood
Agnew’s Water Putty is ideal for filling knotholes, nail holes, oversized screw holes, and other defects in wood. Leave the putty uncoloured if it is to be painted, or coloured if it is to be matched with the wood.
Fix Door Bumpers
Tighten loose door bumpers and trim with Agnew’s Water Putty. Simply ll the oversized hole with putty, insert the bumper and let set. It may hold better than when originally installed.
General Repair Uses
Use Agnew’s Water Putty to patch cracks and holes in walls, repair furniture, tighten loose wood joints, ll holes in wood so dowels and/ or screws can be reset, ll edges and imperfections in plywood, and repair all kinds of antiques.
Ideal for levelling floors or ramping for minor floor level variations. Can be used on concrete, timber and ceramic tile substrates
Patch Cracked Plaster Walls
Use a putty knife to spread Agnew’s into cracks and cavities of plaster walls. Agnew’s Water Putty does not shrink so the cracks disappear. Plus, your Agnew’s Putty repair will last and last.
Filling knot/nail holes, Filling oversized screw holes, Defects in wood
Ensure that the substrate is sound (no loose floorboards, rotted wood, loose mortar, etc.), free from dirt, oil, dust, flaking paint or other contamination and not impregnated with a sealant. Do not prime first. If already primed, sand and provide some keying. If applying a clear finish to say, the punched nail holes on timber ceiling or wall cladding, to minimise the spread and need for excessive sanding you may apply a coat first and then ll. Any excess will then easily wipe off.
Add 3 parts filler to 1 part water in a clean vessel and blend into a workable paste. A stiffer mix makes work easier on a vertical surface (lightly dampen surface first). A thinner mix makes work easier on a floor with many defects.
Agnew’s Water Putty can be coloured by adding oxides, dry colour tinters, acrylic paints, etc, however too much can critically retard setting.
Press the filler firmly into the effect and smooth with a putty knife. Slightly over ll and after 30 minutes, scrape level or shape as required. A light wipe of a damp sponge can give a smoother finish.
The filler begins its initial set in about 20-30 minutes and cannot be effectively thinned or worked after this. In 2-3 hours the filled area can be sanded.
Agnew’s Water Putty is not a moisture barrier. If the substrate and/or Water Putty are not dry, moisture can be trapped under impervious finishes or coverings with unsightly or damaging effect. For finishes or coverings that can “breathe” allow 2-3 hours drying time. For impervious finishes allow 24 hours.
For more information call us on 1800 354 811 or email email@example.com
© Copyright 2018 Timbermate Group. All Right Reserved